CHAPTER A few dition demands additional voltage to fireplace under really hard acceleration. Change with a new spark plug. Preignition In case the electrodes are melted, preignition is almost cer- tainly the cause.
The torque adapter demonstrated in Determine 19 is accustomed to tighten a fastener that cannot be arrived at mainly because of the sizing of your torque wrench head, push, and socket.
As these connec- tions warmth up, the link or joint expands and separates, Voltmeter creating an open circuit. Other warmth relevant issues come about each time a element begins to fall short as it heats up.
BRAKES five. Close the bleed valve and disconnect the vacuum tool or 4B. Open up the bleed valve and apply the brake lever to your hose. pump to power brake fluid from the road. 4. Disconnect the brake bleeder and take away it from your six.
CHAPTER ELEVEN the piston motion is rough or sluggish, the spring could be improperly set up. Take out the best and reinstall the spring. sixteen.
The bend on the mini-ape handlebar and its pull-back riser Blend with full-duration rider footboards as well as a two-up touring seat to supply most Switchback riders all-working day convenience.
Your Using moods improve—so let them. With its detachable windshield and saddlebags, the Switchback bike could make the swap from cruising to touring or back again in seconds. Conveniently get them off for a strong, head-turning Avenue cruiser. Re-connect them for a comfortable, mild-dealing with tourer that surely goes the space.
CHAPTER SIXTEEN Inspection It's not important to get rid of the disc within the wheel to inspect it. Modest marks on the disc will not be vital, but ra- dial scratches deep adequate to snag a fingernail cut down brak- ing effectiveness and enhance brake pad have on. If these grooves are identified, the disc need to be resurfaced or changed.
of the pursuing can be the cause: 1. Electromagnetic Interference: Other Digital devices, electricity strains, or other electromagnetic sources can lead to the Good Safety Process to operate inconsistently. a. Confirm that the fob is not in a steel enclosure or in just 3.0 in. 76 mm of any other Digital equipment. b. Spot the fob on the seat and convert the ignition key to IGNITION. Right after the module disarms, return the fob to a easy locale. read more c. Move motorbike at the very least fifteen feet 5 m from the place of interference. two. Discharged Fob Battery: Use the PIN to disarm the module. Replace the battery. Refer to Fob Battery. 3. A Destroyed Fob: Use the PIN to disarm the bike. Replacement fobs are obtainable for acquire from a HarleyÂDavidson supplier. Siren If the siren does not chirp two or three instances on a legitimate arming command from the stability module, the siren is either in the Chirpless Mode, not linked, not Performing, or the siren wiring was opened or shorted while the siren was disarmed. If the siren is armed and the inner siren battery is lifeless, shorted, disconnected, or has long been charging for a period longer than 24 hours, the siren will respond with 3 chirps on arming as a substitute of two.
Do not operate the motor at really significant RPM with clutch disengaged or transmission in neutral. Jogging an motor at higher RPM can consequence in engine damage. (00177a) The utmost advised safe engine speed is 9000 RPM. Do not idle motor unnecessarily for a lot more than a handful of minutes with motorcycle standing continue to. Do not exceed the greatest Secure RPM specified beneath underneath any problems. Exceeding the utmost safe motor RPM can final result in machines hurt. (00248a) Notice: The greatest advisable engine speed for VRSC product motorcycles is 9000 RPM. If bike will not be ridden for a period of time of three weeks or far more with stability program armed, it can be proposed to connect a Battery Tender to sustain battery cost. If safety process will likely not be armed, it is recommended that the 40 Amp maxiÂfuse be taken off. See Electrical Defense: VRSC Styles.
AroundÂtightening can lead to reduction of car or truck control, which could outcome in Demise or major injury. (00031b) 3. Unscrew the throttle friction adjustment screw so the throttle returns to the idle placement when the hand is taken off from the grip. four. Screw the throttle adjustment screw in to increase friction on grip. This gives a damping influence on throttle movement. NOTE: The throttle friction adjustment screw should not be used under regular quit and go operating circumstances. Clutch Hand Lever Do not place fingers in between hand Manage lever and handlebar grip. Improper hand positioning can impair Manage lever operation and induce decline of car or truck Regulate, which could consequence in Demise or critical injuries. (00032a) See Handlebar Controls: VRSC Versions. The clutch hand lever (1) is located on the left handlebar and is operated with the fingers of the remaining hand. one. Slowly and gradually pull clutch hand lever in in opposition to handlebar grip to completely disengage clutch.
ELECTRICAL Procedure b. To the socket housing aspect, the tangs are located at the top of each and every chamber. The pin terminal slot, on the exact same aspect since the crimp tails, should face upward.
 Whilst armed, the starter and ignition are disabled and the rider might leave the motorcycle knowing that the module will activate an alarm if someone tampers with the ignition or attempts to move the motorcycle. If the fob is existing, the module will automatically disarm when the ignition vital is turned to IGNITION or Obtain. Be aware: Do not relocate the module or the antenna on the bike.
You would like a ride that rumbles—not begs for mercy—whenever you lean on it a bit. The Six-Velocity Cruise Travel delivers clean, tranquil shifting and lowers engine speed around the highway, so you receive a better match between engine turnover and road velocity.